• Skip to primary navigation
  • Skip to main content
  • Skip to footer
Solvent Kleene

Solvent Kleene

Non-Hazardous Degreasing and Paint Stripping Products

978-777-7860
[email protected]

  • Home
  • Products
    • Degreaser/Cleaners
      • D-Greeze 150D
      • D-Greeze 500
      • Tube & Pipe Degreaser
      • D-Greeze ES-LO
      • D-Greeze 1000
      • Electronic Flux Remover/Degreaser
    • Industrial Depainter
      • D-Zolve 319 Room Temperature Powder Coat Dissolver
      • D-Zolve 1012 Room Temperature Powder Coat Dissolver
      • D-Zolve 917 Low Temperature
      • D-Zolve 917 Multi-Purpose
      • D-Zolve 917 for Depainting Silicone Masking Plugs
      • D-ZOLVE 917 Extreme Heat Resistant Powder Coating Remover
      • D-Zolve 1220 for Spray/Brush-On Applications
      • D-Zolve Removes CARC – Chemical Agent Resistance Coating
      • D-Zolve 3251
      • D-Zolve 338 Thermoplastic Powder Coat Remover
      • D-Zolve 15-33IM Fast Acting Powder Coating Dissolver & Paint Remover
    • Aircraft Depainters
      • D-Zolve 15-33R Aircraft Depainter
      • D-Zolve 15-33IM Immersion Aircraft Depainter
    • Non-Slip Coatings Dissolvers
    • Electronic/Electrical Cleaners
      • D-Greeze ES-LO
    • Carbon Deposit Removers and Firearms Cleaners
      • D-Zolve 339
    • Wheel & Rim Restoration
      • D-Zolve 917 Low Temperature
      • D-Zolve 1012 Room Temperature Powder Coat Dissolver
  • About Us
  • Contact Us
D-Zolve 1220 Paint Stripper
  • Clings to Vertical Surfaces
  • Slow Evaporation
  • Multi-Coat Penetration
  • Non-Toxic and Non-Flammable

  • Strips Paints and Powder Coatings

REQUEST A SDS

D-Zolve™ 1220 Paint Stripper

D-Zolve™ 1220 Paint Stripper

D-Zolve™ 1220 is designed to remove hard to strip aircraft paints, painted fiberglass with marine paints, catalyzed polyurethanes with epoxy primer and alkyds. It can be used on aluminum, low strength carbon steel, stainless steel, fiberglass and other metal and plastic substrates.

Properties

When applied to painted surfaces, D-Zolve 1220 penetrates paint layers causing the primer coat to break the bond with the solid substrate and lift together with the topcoat as a single film. Uniform application of D-Zolve 1220 results in a uniform paint lift. The surface to be stripped should be free of oil or any solid contaminants which can interfere with the process of lifting the paint. Effective at removing MIL-PRF-23377 primer.

Small Area Application

For small areas, D-Zolve 1220 can be applied using a soft paintbrush with thin bristles. It is most effective when applied uniformly, without any voids, in one direction. It can also be airless sprayed.

Large Area Application

Efficient application to large areas can be accomplished by spraying D-Zolve 1220. The spray system should be an airless type. The spray nozzle should be non-atomizing so as to reduce mist and over spray. D-Zolve can be directly pumped from its shipping drum. The air activated pump should have Teflon packing. The flexible liquid hose should have flexible woven stainless steel sheathing and a Teflon or Nylon inner hose. Applying the paint stripper to a fiberglass boat or aircraft should be started from the bottom up. If any areas are void of D-Zolve 1220, those areas will need to be applied again. If the application is too thin, a second application may be needed.

Performance

Allow D-Zolve 1220 to penetrate and lift the painted area. The lifted paint will be soft and very easy to remove. Once the paint film has lifted, it can be removed with a plastic spatula, squeegee, or a bristle broom. The lifted paint should be collected for disposal. After the paint has been removed, the surface can be washed off with high-pressure water. The paint lift time can be greatly reduced if the surface temperature is 85°F or higher. To increase the surface temperature, infrared heating lamps are efficient and economical. Allow 2-6 hours for the paint to lift.

Click here for D-Zolve 1220 technical data sheet

Caution: D-Zolve 1220 is a water-based product which is Formic Acid activated. It should be used with good ventilation. Protective clothing such as gloves, goggles or face shield should be used. Also suggested is using a NIOSH approved respirator with a mechanical filter. For first aid information, see the MSDS. Avoid contact with eyes, skin and clothing.

Disposal

See SDS for disposal information. To meet local pH requirements, the rinse water can be pH adjusted if necessary.

Footer

Transene Company, Inc.

Solvent Kleene Brand
10 Electronics Avenue
Danvers MA  01923

Tel: 978-777-7860
[email protected]

  • Contact Us
  • Request An SDS
  • Back to Top
  • Product Listing