D-Greeze 1000 Degreaser/Cleaner
 |
D-Greeze™ 1000 is an industrial grade replacement for chlorinated and other hazardous solvents. While maintaining the aggressive cleaning action of Solvent Kleene's non-hazardous degreaser/cleaner, D-Greeze 500, D-Greeze 1000 is designed for applications where faster drying is preferred. Like D-Greeze 500, D-Greeze 1000 outperforms Trichloroethane and other chlorinated solvents. With its low surface tension, D-Greeze 1000 is able to quickly penetrate soils and provide fast cleaning. D-Greeze 1000 was formulated to feature a faster evaporation rate than most non-hazardous products, enabling it to dry more quickly. The chemical grafting of its components enables D-Greeze 1000 to quickly respond to air blow-off which reduces drying time to seconds. Safer work environment As a choice replacement for chlorinated and other hazardous solvents, D-Greeze 1000 is non carcinogenic, has a very low order of toxicity, is non corrosive, non reactive, and non flammable with a flash point of 111°F. It has a clean, mild odor. It contains no chlorinated com-ponents or SARA-listed chemicals, no halogens, and no CFCs or ozone depleting components. Cleaning with D-Greeze 1000 Quick penetrating D-Greeze 1000 dissolves and emulsifies stamping oils, lubricating oils, lubricating fluids, cutting oils, and greases. It will also remove adhesives, wax, flux, and inks. D-Greeze 1000 can be used in existing cleaning equipment without the need for any major capital expenditure. Most other safe degreaser/cleaners, especially water-based products, require costly specialized equipment for heating, constant chemical balancing, deionized water rinsing, waste water treatment, and sewer monitoring. For immersion cleaning, D-Greeze 1000 can be used in most any existing tank. A vapor degreaser can be used after disconnecting the heater. To shorten the cleaning cycle, a pump charged liquid circulation system can be used to produce an aggressive liquid flow. The introduction of fluid dynamics facilitates the pulling off of oils and other contaminants from intricate surfaces, irregular channels, or long tubing. Room temperature drying Drying time can be dramatically reduced by blowing either high pressure compressed air or low pressure high velocity air at the wet surface. The air can be delivered through an air spray gun, spray manifold, or an air knife. D-Greeze 1000 with its low surface tension is very quickly stripped off the inner and outer surfaces. D-Greeze 1000 leaves a surface spotlessly clean and residue free. Care must be taken, however, that blow-off operations are conducted within an enclosure. This allows the capture of the removed liquid for reuse as well as prevents any mist to come in contact with ignition sources, such as, an unprotected electric motor which can arc or spark. The cleaning tank and liquid blow-off area should include a gentle exhaust and ventilation system to keep the air from becoming stagnant and preventing even mild odors from accumulating. This is particularly true when the ambient air is high in humidity. D-Greeze 1000 and the described drying method will result in a clean and residue free surface, suitable for brazing, painting, plating, or other metal finishing requirements. Disposal Spent D-Greeze 1000 has a high BTU value making it useful for fuel blending. Incineration is an efficient and inexpensive method of disposal. Meets Federal and State Regulations Section 313 of the Superfund Amendment and Reorganization Act (SARA) mandates that a facility must report to the EPA the use and release of specific toxic chemicals. D-Greeze 1000 does not contain any of the components listed in Section 313 toxic chemical list. And, as defined in the Clean Air Act Amendment of 1990, D-Greeze 1000 is not a hazardous air pollutant. Compatible with VOC regulations, D-Greeze 1000 is not photochemically reactive as defined, for example, by California South Coast Rule 102. Unlike toxic or carcinogenic conventional solvents such as Xylene, Toluene, Mineral Spirits, D-Limonene, Trichloroethane, Percholoroethane, Methylene Chloride, and Trichloroethylene, D-Greeze 1000 contains no halogens, no carcinogenic components, and has a very low degree of acute oral and inhalation toxicity. Material compatibility D-Greeze 1000 can be used at room temperature for a wide range of materials as indicated in the chart below. METALS stainless steel carbon steel aluminum magnesium titanium cobalt copper brass PLASTICS PVC ABS acrylic fluorocarbon nylon polycarbonate ELASTOMERS Viton™ Kalrez™ polysulfide polyester Technical Support To help D-Greeze customers, Solvent Kleene's technical team provides assistance and support in adapting existing equipment, improving cleaning techniques, reducing drying times, and reducing waste.
|
|
|